齒輪油泵kcb-18.3小功率齒輪泵作為原油輸送泵流量18.3l/min,壓力:1.45mpa

齒輪油泵kcb-18.3小功率齒輪泵作為原油輸送泵流量18.3l/min,壓力:1.45mpa

尊敬的(de)客戶您好:

公司已通過iso9001：2000國際質量體系認證，中國船級社ccs型式認證，法國船級社bv産品工廠認證，美國船級社abs産品質量認證，成為中石油物資資源市場成員、中石化物資資源市場成員，并列入武器裝備科研生産保密資格名錄可以承擔軍隊系統裝備部門的涉密武器裝備科研生産合同項目。河北省知名産品生産企業，船用泵産品承制企業。我們(men)的産品是：同樣的價格我們的(de)質量更優、同樣的質量我們價格更低、同樣的(de)産品我們(men)服務更好。

　kcb齒輪泵安裝: kcb gear pump installation:

　　1、泵安裝前應檢查泵和電機在運輸過程中是否受到損壞，如電機是否受潮，泵的進出口防塵蓋是否損壞而使污物進入泵腔内等。1, before the pump installation, should check the pump and motor is damaged during the transit, whether be affected with damp be affected with damp such as motor, pump the import and export of dust cover for damage and make the dirt into the pump chamber, etc.

　　2、泵在搬運過程中，應選擇合适起吊位置，減少泵的變形。2, pump in the process of handling, should choose appropriate lifting position, reduce the deformation of the pump.

　　3、泵的底座應固定在牢固的(de)基礎上，以免産生振動影響泵的正常工作。3, the base of the pump should be fixed on the basis of the strong, so as to avoid vibration influence the normal work of the pump.

　　4、泵的進出口管路應清理幹淨不得存有硬顆粒的報告雜物。4, import and export of pipeline of pump should be cleaned up shall not have the report of hard particles sundry.

　　5、管路口徑一般不小于泵的進出口徑，進油管路應盡量短，并減少彎路。必要時在進油口安裝金屬過濾器，過濾器的有效面積不應小于管道過流面積的(de)三倍。5, pipe diameter is generally not less than the in and out of the caliber of pump, the oil pipeline should be short, as far as possible and less detours.when necessary, metal filter is installed on oil inlet filter effective area should not be less than three times of pipe flow area.

　　6、安裝時，不得用泵來承擔管路的重量。7、用手轉動聯軸器，泵應轉動靈活，不得有過緊或輕重不均現象，如有應立即排除。

6, when installation, must not use the pump to bear the weight of the line.7, turn the coupling with the hand, the pump should be flexible rotation, can not have too tight or weight uneven phenomenon, should immediately ruled out.

　　kcb齒輪泵的開機: kcb gear pump of the boot:

　　1、開機前應檢查泵軸轉動是否靈活，有無卡阻現象，進出口管道上的閥門是否開啟，泵的(de)轉動方向是否正确。1, should check whether the pump shaft rotation is flexible, before starting the presence of jam phenomenon, import and export pipeline valve is open, the pump rotation direction is correct.

　　2、長時間沒有使用的(de)泵開機前應向泵腔中注入一定量的潤滑液，以減少泵在吸油過程中的幹摩擦，并可提高泵的自吸性能。2, long time no use the pump to the pump before starting the cavity inject a certain amount of lubricant to reduce the pump in the dry friction in the process of oil absorption, and can improve the self-priming performance of pump.

　　3、開機後如有不正常的噪音或過熱現象，應立即停車檢查。3, after the boot if there is any abnormal noise or overheating phenomenon, should immediately stop check.

　　4、檢查泵軸端有無洩漏現象，如：對填料密封應适當調緊壓緊蓋，其它密封則應拆機檢查；4, check whether there is any leakage on the pump shaft end phenomenon, such as: the packing should be properly tighten clamp cover, other sealing should teardown check;

　　5、若輸送熱油，在開機時應均勻預熱，預熱是利用被輸送的介質不斷通過泵體進行的。預熱标準：吸入口的油溫不得高于泵體溫度40，預熱的升溫速度控制在＜40/h，在預熱時應将固定泵體的螺栓松開，預熱完畢，将其擰緊。在預熱過程中，應注意觀察泵的(de)運行情況，以但發生不良情況，應立即停泵檢查。5, if conveying hot oil, the boot should be uniform preheating, preheating is to use the media constantly through the pump body to be delivered.preheat standard: the inlet oil temperature shall not be higher than the pump body temperature 40, the preheating temperature speed control in the < 40/ h, when the preheating bolts should be fixed pump body loosen, preheating and tighten it.should be paid attention to in the process of preheating, observe the running situation of the pump, with adverse event, however, should immediately stop check pump.

　　6、泵停機後，首先切斷電源，然後關閉進出口管道上的閥門，避免造成泵倒轉。after six, pump stop, cut off power supply first, then close the import and export pipeline valve, avoid to cause back pump.

　　7、泵經過長期使用，壓力流量有明顯下降時，應拆泵檢查，更換其己磨損的零件。　　

齒輪油泵kcb-18.3小功率齒輪泵作為原油輸送泵流量18.3l/min,壓力:1.45mpa